Description
- Brand: Stein
- Type: Thermal Oil Fryer
- Model: TFF II 4028
- Date of Remanufacture: 2024
- Conveyor Belt Width: 40 Inches (Usable)
EQUIPMENT SUMMARY:
DESCRIPTION OF LABOR AND MATERIAL, REMANUFACTURED STEIN TFF II4028 BASE MACHINE:
• Repair Functional Damage by Replacing Sheet Metal and Tubing as Required
• Seal Visible Cooking Oil Leaks
• Install and Plumb Nozzles for Fire Suppression System
• Fabricate New Doors and Track assemblies as Required
• Install New Piping and Level Pump
• Install New Electrical Components and Wiring
• Replace Hood Limit Switch assemblies
• Install New Sediment Auger and Seals
• Install New Submerger Hold-Down Components
• Other Repairs, as Required Machine Mounted Co2 System
• 4 Release Nozzles
• New Piping
• New Pressure Switch
• New Pressure Trip
• 4 Temperature Detectors
• Pre-Piped to Single Connection Point on The Machine and A Second on The Steam Vent
• Pre-Wired Detection System; Wire Pulled to Main Junction Box
• Pressure Switch and Detectors and Replaced Fryer Hood & Steam Vent
• Repair Minor Damage by Replacing Sheet Metal and Straightening as Required
• Verify Hood will Fit on Fryer Tank as originally Designed
• Install Stainless Steel Conduit and Junction Boxes and Thermal Detectors for Fire Suppression System
• New Steam Vent to be Manufactured and Supplied with The Machine
• Including (3) Mist Filters and Fire Suppression Components.
LIFT SYSTEM & HEAT EXCHANGERS:
• New bearings and Shafts Throughout
• New Screw Jack Assemblies Featuring Long Life Mechanical Screw Jacks
• New Stainless Steel Couplings
• New Miter Box assemblies (wash Down Duty or Stainless Steel)
SEDIMENT CONVEYOR, NEW:
• New belt Supports
• New Wear Strips
• New Shafts
• New belt and Sprockets
• New Seals, Hubs, etc.
• New Sediment Auger and Drive Components
PRODUCT CONVEYOR, NEW:
• 28 Ft Fry Length
• 3/8 X .062 Flat Flex Conveyor belt
• Polished Side Bars
• Electric Drive
• Adjustable Infeed Shaft
SUBMERGER CONVEYOR, NEW:
• Infinitely Adjustable Infeed Shaft Height
• 3/8 X .062 Flat Flex Conveyor belt
• Polished Side Bars
CONTROLS:
• Allen Bradley PLC and Interface
• New Control Panel
• All Machine Functions Controlled From Interface
• NEMA 4x Cabinet
• Control Cabinet Field Installed by Others
MACHINE WIRING:
• All Wiring and Electrical Components to be Replaced
• Wiring to be Completed According to Omar associates Wiring Diagrams
• All Wiring to be Pulled to Junction Box Located on Fryer Frame
• Level Controls (Low Level and Oil Level Switches) to be Replaced
DOCUMENTATION & TESTING:
• Machine assembly Drawings Included to Facilitate Repair and Part Procurement
• Wiring Diagrams Included to Facilitate Repair
• Fire Suppression assembly and Wiring Diagrams
• Utility Drawing for Installation Planning
• Fryer Tank to be Filled with Water and Checked for Leaks
• All Electrical Circuits will be Checked for Proper Operation
• Conveyors will be Operated to Verify Proper Alignment and Adjustment
• Inspection of Heat Exchanger to Identify Potential Carbon Build Up
• All Testing will be performed Cold
• Machine and Loose Parts will be Skidded for Domestic Shipment
OPTIONAL OFF-MACHINE FIRE SUPPRESSION COMPONENTS, MAIN & RESERVE:
• CO2 Cylinders
• Cylinder Hoses
• Control Heads
• Discharge Heads
• Cylinder Rack
• Control Panel
• Kidde-Supplied Engineering Drawing for Field Installation per NFPA Code
• All Components to be Installed and Inspected by Others
OPTIONAL COOKING OIL SUPPLY TANK:
• 304 Stainless Steel Construction Throughout
• Four Ports; Two-Inch Diameter Sanitary Connections Located In Tank Side Above Bottom
• NPT Connection for Level Switch
• Cone-Shaped Bottom with Center Drain
• 1,600 Gallon Capacity
• Hinged Lid with Fill Connection
• Glass Bead or Polished Finish
OPTIONAL HOT OIL PIPING PACKAGE:
• Interconnection of (1) Stein TFF II 4028 Fryer, (1) 1,600 Oil Supply Tank, (1) Omar OF-11 Filters
• Sanitary Ball Valves Rated for Hot Oil
• Necessary Pipe Support Stands
• Elbows, Clamps Gaskets, Butt-Weld Ferrules, etc. as required
• Components Ship Loose for Field Fabrication, Assembly, and Welding
OPTIONAL COOKING OIL FILTER, OMAR MODEL OF-11:
• Stainless Steel Centrifugal Feed Pump
• Stainless Steel Centrifugal Suction Pump
• Pumps and Piping Set Up to Facilitate Filling Fryer, Pumping to Tank, and Hot Oil Circulation
• 10-15 Gallons/Minute Nominal Continuous Flow Rate
• Machine-Mounted Valves to use Suction Pump to Transfer Oil to Fryer or Oil Supply Tank
• Stainless Steel Filter belt
• 80 Micron belt
• Positive, Continuous Belt Drive
• Stainless Steel Filter belt Drive Chain
• forced Flow Circulation System
• Stainless Steel Construction
• Continuous Outlet Flow
• Inlet Flow Controlled by Float Switch
• Flat Cover Over Filtration Area to Minimize Oil Splash and Oil Cooling
OPTIONAL SPARE PARTS PACKAGE:
• Bearings
• Belting
• Screw Jacks
• Wear Strips
• Temperature Detectors
• Thermocouples
• Other Wear Parts
OPTIONAL STARTUP SUPPORT BY OMAR FIELD MECHANICS:
• Electrical Termination
• Thermal Fluid System Setup
• Rigging
• Production Setup, Testing, Training, and Optimization
> Construction: Stainless Steel/Food Grade Materials
> Condition: Remanufactured
> Power: 480 VAC / 3 Phase / 60 Hz
> Previously Used for: Food Production
> * NOTE: This Fryer Requires a 2.8mm BTU/Hr Thermal Fluid Boiler/Heater and a Thermal Fluid Supply of 354 Gpm at 500° F.
HEATER SYSTEM PRICING AND DELIVERY LEAD TIME:
Stein TFF II4028, Remanufactured ………………..$ 297,000.00
** Optional Off-Machine CO2 Supply System …………$ 57,600.00
** Optional Off-Machine Reserve CO2 Supply System ….$ 48,320.00
** Optional Cooking Oil Storage Tank ……………..$ 18,400.00
** Optional Hot Oil Piping Package ……………….$ 13,300.00
** Optional Cooking Oil Filter, OF-11 …………….$ 72,400.00
** Optional Spare Parts …………………………
Total Price Including all Options ………………..$ 534,320.00
An on-site inspection is often the best way to determine if the prospective machine or equipment will suit your needs. An inspection prior to purchase will help ensure a positive purchasing experience. To arrange an inspection or if you should have comments or questions or need any additional information, please feel free to contact us at any time.
Don McMahan cell: 404-219-6999 email: ultracopy2@yahoo.com
Steve Garren cell: 214-883-3812 email: foodfactories@gmail.com
DESCRIPTION OF USED EQUIPMENT. The above description of Used Equipment & Manufacturer Specifications is based on information available to JLM at the time of this writing. JLM, however, makes no warranty, express or implied, as to the description of any of the Used Equipment or Manufacturer Specifications provided. Machinery quoted used, as is, where is and subject to prior sale, except as expressly set forth otherwise. Payment Terms: Full Payment Prior to Shipping.